- Generate Rsa Key Command
- Crypto Key Generate Rsa General Keys Modulus 1024 Error Codes
- Crypto Key Generate Rsa General Keys Modulus 1024 Error 1
A: In the IOS config, you can define the size of the RSA keys that secure the server, and AMP's SSH package has a minimum required size. The size of the key on your APs has to be increased to at least 768. It's pretty easy to do. Here's the command to increase it to 1024 from the cli: crypto key generate rsa general-keys modulus 1024.
Jun 11, 2019 SW1 ( config)# crypto key generate rsa. How many bits in the modulus 512: 1024% Generating 1024 bit RSA keys, keys will be non-exportableOK Set the size of key to 1024 bits. If your Cisco Switch is running an older version of Cisco IOS image, then it is extremely recommended that you upgrade to latest Cisco IOS. RSA (Rivest–Shamir–Adleman) is one of the first public-key cryptosystems and is widely used for secure data transmission. In such a cryptosystem, the encryption key is public and distinct from the decryption key which is kept secret (private).
今日はSSHの設定方法を勉強します。
まだまだTelnet接続を使用している環境も多いと思いますが、世の中的にはManagementアクセスもよりセキュアにする方向に向かっているので、Telnetは割愛しました。
まだまだTelnet接続を使用している環境も多いと思いますが、世の中的にはManagementアクセスもよりセキュアにする方向に向かっているので、Telnetは割愛しました。
Catalystに192.168.1.1を設定し、SSHによるリモートアクセスを確認します。
![Keys Keys](/uploads/1/2/6/0/126087002/705516220.gif)
IPの設定とインターフェースの開放
ログインUsernameとPasswordを作成し、vtyに設定。接続方法をSSHに限定。
ホスト名、ドメイン名の設定、RSA鍵の作成
SSHv2に限定
特権パスワードの設定
UsernameとPasswordはコンソール接続、リモート接続で共通のものを
http://qiita.com/jinnai73/items/a240bf2bc1325b46edfe
パスワードを作成したら
username secret
コマンドで設定します。password
コマンドでも設定できますが、セキュリティ上username secret
を使用することが推奨されます。この辺りは前回書きました。http://qiita.com/jinnai73/items/a240bf2bc1325b46edfe
パスワードを作成したら
login local
コマンドでlineに適用します。Telnet接続を禁止するため、transport input
コマンドでsshでのログインのみ許可します。続いてSSH接続に必要なRSA鍵を作成します。RSA鍵を確認するコマンドは
show crypto key mypubkey rsa
です。何も入っていませんね。鍵を生成するコマンドは
crypto key generate rsa
ですが、生成する前提としてスイッチのFQDN、つまりホストとドメイン名が決まっている必要があります。デフォルトではドメイン名が設定されていないため、以下のようなエラーが出ます。ドメイン名の設定は
ip domain-name
コマンド、確認はshow hosts
で行えます。それではホスト名とドメイン名を設定しましょう。
設定できました。これでRSA鍵も生成可能になります。
crypto key generate rsa
コマンドで生成、鍵長は2048 bitを指定します。警告メッセージにもある通り、2048 bitでは約1分ほど時間がかかりますが、2016年現在1024 bit以下のRSAは(少なくともインターネット上では)使わない方が良いというのは異論が無いところでしょう。
この時点でSSHでの接続が可能になります。テストのため自分自身に接続してみましょう。
できました。sshのv1はセキュリティに問題があるため禁止しましょう。一度ログアウトして、sshをv2に限定したのちに、v1での接続ができないことを確認します。
うまくできています。この状態ではSSHアクセスした後に特権モードに入ろうとしてもできないため、
enable secret
で特権パスワードの設定もしておきましょう。思ったよりボリュームが増えてしまいました。明日ももう少し、機器管理を勉強しようと思います。
Configuration of SSH on Cisco Switch in Packet Tracer 2019
This Article is about the configuration of SSH on Cisco Switch. You can configure SSH on Cisco devices very easily using these simple steps:
- Crate a Packet Tracer Topology Lab
- Basic IP Setting for connectivity
- Set hostname and domain-name on Switch
- Set console and enable password for SSH login
- Generate the RSA Keys
- Setup the Line VTY configurations
- Create the username password for SSH access from PC
- Verify SSH access
For the configurations of SSH in packet tracer on Cisco switch, you are required to follow the above steps. Let start and perform these steps one by one. (Learn what is PSSH)
Crate a Packet Tracer Topology Lab
Our first step is to open the packet tracer and need to create a simple lab. For this topology we will use only one switch and a PC. Simply drag these two items on dashboard. Now we will connect them with straight through connection.
Basic IP Setting for connectivity
The next step is assign the suitable IP setting to these devices. For keeping it simple and making basic connectivity we will assign just two IP address to these device. We will assign the IP address to PC. For this will open the PC setting and then IP configuration. Here we will assign an IP address to host, in our case we are going to assign it 192.168.1.1 with the default gateway. For default gateway we will assign the IP address 192.168.1.10. We assign the second IP address to our Vlan1 interface on switch. And its IP address will be the gateway of host that is 192.168.1.10. For this we will use the basic commands.
Switch> enable
Switch# config t
Switch(config)#interface vlan 1
Switch (config-if)# ip address 192.168.1.10 255.255.255.0
Switch (config -if)#no shut
Generate Rsa Key Command
Once you done with basic IP setting, you can verify the connectivity by pinging the interface vlan1 IP from host.
Set host-name and domain-name on Switch
For SSh configurations you need to configure a host-name and domain-name for your switch you can do this with these simple commands.
Switch # config t
Switch (config)#hostname SW1
SW1 ( config)#ip domain-name w7cloud.com
Set console and enable password for SSH login
For SSH access it is required that you must configure the console and enable password on your cisco switch. You can set these two passwords with following commands.
SW1 ( config)#line console 0
SW1(config-line)#password cisco
SW1(config -line)#logging synchronous
SW1(config- line)#login local
SW1 (config- line)#exit
SW1 # enable secret cisco
Generate the RSA Keys
Your Cisco switch must have RSA keys that for the SSH process. You can generate the RSA keys with following command:
SW1 ( config)# crypto key generate rsa
How many bits in the modulus [512]: 1024
% Generating 1024 bit RSA keys, keys will be non-exportable…[OK]
Set the size of key to 1024 bits.
If your Cisco Switch is running an older version of Cisco IOS image, then it is extremely recommended that you upgrade to latest Cisco IOS.
Setup the Line VTY configurations
For the configuration of SSH on cisco switch you need the following line vty configurations, and input transport is required to set to SSH. Set the login-to-local, & password to 7.
sw1 ( config)#line vty 0 4
sw1 ( config-line)#transport input ssh
sw1( config -line)#login local
sw1(config- line)#password 7
sw1(config- line ) #exit
Create the username password for SSH access from PC
If you do not have a username for SSH access you need to create a username. You can do it with this simple command:
Sw1# config t
sw1 (config ) # username w7cloud password cisco
Crypto Key Generate Rsa General Keys Modulus 1024 Error Codes
Make sure the password encryption services is enabled on your switch, this service will encrypt your password, & when you do “sh run”, you’ll see only the encrypted password, not clear text password.
SW1# service password-encryption
Verify SSH access from Host
Once you done with the above configurations you can test all these configuration by creating a SSH connection from Host. You do it the command ssh –l <username> <IP address>. Open the host command prompt and use the command
C:>ssh -l waqas 192.168.1.10
Crypto Key Generate Rsa General Keys Modulus 1024 Error 1
It will ask for password, provide the password that you created with this username in previous steps. Then it asked for console password and then you need to provide the enable password. Now you are in your Cisco switch. You can perform switch configurations from your host.
From the switch, if you use the command ‘sh ip ssh’, it will also confirm that SSH is enabled on this cisco swith.
For better understanding please watch the video and like it.
I hope this will be a helpful for you, please share your comments. If you like this then share this on social media. Thank you for reading this..!
Guide on Cisco Router Configuration for Beginners
Related: 4 Best SSH Client Used by Professionals